Doremi DSV-J2 Manuel d'utilisateur

D S V - J 2Field Installer ManualVersion 1.3The English version of this document is the only legally binding version. Translated versions are not lega

3 DSV-J2 PresentationThank you for choosing the Doremi DSV-J2. The DSV-J2 is a high quality JPEG-2000 server capable of playing movie or trailer packa

(a) (b)Figure 7: DSV-J2 Front Panel, Right Door Opened, Three HDDs(a) Black Front Panel, (b) Silver Front PanelEach hard disk has a blue but

3.2 DSV-J2 Rear PanelTwo different rear panels can be found on the DSV-J2, depending on the motherboard used. The SuperMicro motherboard is illustrate

4 Rear Panel Connectors4.1 VGA Cable Connection for Server LCD Screen UsageIf the front panel LCD screen needs to be used, the server LCD screen VGA c

4.2 Rear Panel Card Slot Connectors 4.2.1 Card Slot Connectors OverviewOn the center of the rear panel are the various card slot connectors. The only

4.2.2 HD-SDI Serial Digital Interface / Dolphin DCI Decoder CardLocated in the rear panel card slots beside the AES/EBU audio card is the standard-def

The GPIO DVI-I connector pin numbering is illustrated below (Figure 16):Figure 16: Dolphin DCI GPIO (DVI-I) Female ConnectorThe General Purpose I/O DV

The GPIO cable delivered with the DSV-J2 with a Dolphin DCI installed has an exposed wire end as shown here (Figure 17):Figure 17: Dolphin DCI GPIO Ca

Pin#SignalDescriptionPin#Signal Description1 Ch 15 & 16 plus 14 Ch 15 & 16 minus2Ch 15 & 16 ground15 Ch 13 & 14 plus3 Ch 13 & 14 m

 With the LTC Output option (flagged with “LTC” mark above the BNC connector), the connector outputs the linear time-code (LTC) compliant with SMPTE

Table of Contents1 Introduction...

4.3.2 Keyboard & Mouse PS-2 ConnectorsOn the left side of the connector panel are the PS-2 connectors for the PC keyboard and mouse. These jacks c

5 DSV-J2 IP AddressAll DSV-J2 servers are shipped with a default IP address of 192.168.100.50 on the Ethernet port (Eth1) and a DHCP assigned dynamic

9.) Enter the desired device broadcast address then select OK.10.) Select Yes for eth1.11.) Select No for Removable device.12.) Select No for automati

6 Device Manager ConfigurationThe Device Manager is a graphical user interface used to setup the connection between a DSV-J2 and cinema projector(s).

Figure 25: Device Manager GUI – eCNA Device SetupMake sure the Enabled field is checked in the top-right corner of the GUI.Click the Save button in or

6.2.2 JNior Device6.2.2.1 JNior Device AdditionTo use the JNior device, click the Add button and select JNior. The JNior device setting windowshould b

6.3 Raw Device6.3.1 Raw Device AdditionA Raw device allows for communication with an external device across an Ethernet connection using Raw data form

7 Automation Set Up: Macro Editor UsageAutomation events can be created using the Macro Editor for use within the CineLister interface.The paragraphs

7.2 Automation Cue Tab7.2.1 Macro CreationClick the Add button to start the creation of a new Macro Automation Cue (Figure 28). The following window s

7.2.2 Action InsertionTo insert a new action in a Macro Automation Cue, select its Macro name in the Macro Window and click the Insert a New Action bu

Software License AgreementThe software license agreement can be found at the following location:http://www.doremilabs.com/support/cinema-support/cinem

 Example of Delay Action Insertion To add a delay action to the selected Macro Automation Cue, click the Delay button in the Action window and defin

 Example of Automation Library UsageWhen one of the supported devices (e.g. eCNA and JNior) is added according to Section6.2, the Macro Editor should

7.2.3 Action List Management Action ReorderingTwo arrows allow the user to change the order of the actions in the Macro Automation Cue (Figure 36). U

7.3 Trigger Cue Tab7.3.1 Trigger Cue Tab OverviewThe Trigger Cue Tab is shown below (Figure 38):Figure 38: Trigger Cue Tab7.3.2 Trigger Cue CreationTo

The newly created Trigger Cue will appear in the Trigger window, ready to be connected to a GPI event (Figure 40): Figure 40: Trigger Cue DefinedTo ed

Figure 42: Connection to a GPI Event Define the GPI line number and value you want to connect to the Trigger Cue and click the Ok button when you are

7.4 Pre-defined Macro UsageIf you have a pre-defined macros.xml file containing automation and trigger cue definitions, justcopy it into the /doremi/e

8 Time Zone Set UpDSV-J2 units may or may not be localized with your time zone. This section provides you information on how to check and/or change th

9 Vendor Specific Projector Set Up Instructions9.1 Adding a Christie ProjectorTo add a Christie CP2000 projector, run the Device Manager as presented

To perform the projector setup, follow the steps below:1. Specify a projector identifier in the first field – especially if you setup several projecto

WARNING!! THIS DEVICE MUST BE GROUNDED. IMPORTANTPower requirements for electrical equipment vary from area to area. Please ensure that your D

9.3 Adding a Barco ProjectorTo add a Barco projector, perform the same procedure as in paragraph 9.1 using Barco for the Projector model field (Figure

10 DSV-J2 Software/Firmware USB Upgrade Instructions10.1 Displaying the DSV-J2 Software/Firmware VersionsTo display the software version of the DSV-J2

 Click on Ingest. You will be asked for a password to be able to perform this operation (Figure 51): Figure 51: Authentication Window  Enter the app

11 DSV-J2 Linux Terminal CommandsThe DSV-J2 uses the Linux operating system. Here are some basic instructions on how to navigate the Linux interface a

11.2.2 Remote Login From a Windows PCFrom a Windows PC, you need to install a ssh client in order to login remotely. An example sshclient is “PuTTY,”

11.5 Software/Firmware Upgrade11.5.1Sending the Software File to the DSV-J2To send a new software update file to the DSV-J2, use an FTP client and log

11.5.4Performing the Firmware UpgradeTo perform the upgrade of the Dolphin firmware, simply reboot the DSV-J2.To do this, login as root and from a ter

11.7.2RAID ReinitTo reinit the RAID, type the following command:type: sh /doremi/sbin/reinit_raid.sh <enter>CAUTION: This process is a DESTRU

When completed, type: bye <enter> at the command prompt to quit the FTP session. The DSV-J2 will then automatically scan the /data/incoming/ dir

12Troubleshooting12.1 DSV-J2 BIOS SettingsIn case the system does not complete the boot sequence upon powering up, the BIOS settingsmay have to be che

In order to ensure optimum performance of your DSV-J2, select the setup location carefully and make sure the equipment is used properly. Avoid setting

To access the BIOS settings of the DSV-J2 fitted with the SuperMicro X7SBE motherboard, press the Delete key just after powering ON the keyboard when

12.2 Server LCD Screen MaintenanceWhen the server LCD screen needs recalibration, this section provides the required steps tofollow.12.2.1Root Logging

13 Appendix A: General Purpose Output Connection Diagram Typical ApplicationDSV-J2 GPIO CableGPO 0+5V up to +24VDSV-J2Each general purpose output has

14Appendix B: General Purpose Input Connection DiagramDSV-J2 GPIO CableGPIO Male Connector GPIO Cable Female Connector...Typical Application 1:DSV-J2D

15Appendix C: XML Structure Used by Macro EditorThe Macro Automation Cues and Trigger Cues generated using the Macro Editor GUI presented in this docu

</Command> </CommandList> </AutomationCueMacro> <TriggerCue> <Name>Trigger_1</Name> <Id>urn

15.2.1IssueDate NodeThe IssueDate node is used to define the time and date at which the AutomationCueMacroListXML file was issued. It is meant for dis

15.2.5.2 Id NodeThe Id element uniquely identifies the AutomationCueMacro for asset management purposes. It is encoded as an urn:uuid per [RFC 4122].1

15.2.6.1 Type Sub-NodeThe available types of commands are listed below:Table 1: Command Types AvailableType DescriptionBlack Black video and silent au

The format of this Value element also depends on the kind of command type. The table below presents the usage of such elements for each command type:T

C A U T I O NR I S K O F E L E C T R I C S H O C KD O N O T O P E N !C A U T I O N : T O R E D U C E T H E R I S K O F

15.2.7TriggerCue Node [optional]Each TriggerCue element corresponds to all the parameters defining a TriggerCue. Theseparameters

15.2.7.4 CueType Node [optional]The CueType element corresponds to the type of Cue used by the TriggerCue. The availableCue Types are listed in the ta

15.3 SchemaThe XML Schema document presented in this paragraph defines the structure of a Macro Automation Cue List using a machine-readable language.

<!-- CueTypeParameters --><xs:complexType name="CueTypeParametersType"><xs:choice><xs:sequence><xs:element name=&

15.4 XML Diagram LegendThe following provides a legend for notation used in diagrams depicting XML structures.15.4.1Element symbolsIn the schema desig

xsd:string (for example), content = simple. The three lines in the upper left corner are used for both text and numeric content.15.4.2Model symbols (&

15.6 Model groups and referencesAn element group is a named container with one or several elements. The group of elementscan be reused at multiple pl

16 AcronymsTerm DefinitionFPS Frames Per SecondGPI General Purpose InputGPO General Purpose OutputHDD Hard Disk DriveLCD Liquid Crystal DisplayLED Lig

17 Document Revision HistoryDate Version Description03/17/2009 1.0 First version.07/26/2012 1.1 Logo updated and contact information added.08/29/2013

1 Introduction1.1 PurposeThis manual is designed to guide you through the setup and installation of the DSV-J2. It provides information about the foll

2 Caution2.1 Drives Insertion2.1.1 General RuleDo not insert drives if the unit is powered on.2.1.2 HDDs ShipmentDrives (HDDs) might be shipped out of

 Insert each drive all the way, one by one, in the chassis HDD cage according to the TOP-CENTER-BOTTOM location defined in the schema below and while